Author Topic: refit connie (Read 18226 times)

Shino Tenshi · « **Reply #100 on:** May 06, 2009, 11:15:16 AM »

403 Forbidden

That's what I see :lol:

Nebula · « **Reply #101 on:** May 06, 2009, 11:18:29 AM »

yeah they don't like hotlinking anymore either...

baz1701 · « **Reply #102 on:** May 06, 2009, 11:19:29 AM »

how about this pic of the actual model

baz1701 · « **Reply #103 on:** May 06, 2009, 03:04:22 PM »

re-profiled the impulse

CptBenSisko · « **Reply #104 on:** May 06, 2009, 05:24:55 PM »

make the width of it a little less...and shorten the impulse deck on the edge of the saucer vertically

Shadowknight1 · « **Reply #105 on:** May 06, 2009, 05:34:49 PM »

Yeah, what he said. You're getting there though.

baz1701 · « **Reply #106 on:** May 06, 2009, 05:38:09 PM »

already sorted it

CptBenSisko · « **Reply #107 on:** May 06, 2009, 06:29:48 PM »

i know you're gonna hate me..cuz im bein critical..but..you shortened it a little too much..bring it down a tiny bit..and bring the side angular pieces that are on the connecting dorsal up so they support the impulse deck cuz thats what they do LOL and don't hate me LOL

baz1701 · « **Reply #108 on:** May 06, 2009, 06:56:38 PM »

Your right I hate you

But I listen, adjusted the impulse deck again. It is now as near as damit.

Also start the texture for the saucer. I know the grid lines don't line up yet, like I said it is a start.

FourChan · « **Reply #109 on:** May 06, 2009, 08:15:46 PM »

Looking sweet, is this going to have the low power/high power deflector?

Adonis · « **Reply #110 on:** May 06, 2009, 09:11:05 PM »

Baz, before you even attempt any form of texturing on her, you might would want to boolean the whole thing together (cause I can see you didn't). That way the model will damage correctly ingame and stuff. BC's engine like seamless, clean meshes.

baz1701 · « **Reply #111 on:** May 07, 2009, 03:52:57 AM »

Quote from: Adonis on May 06, 2009, 09:11:05 PM

Baz, before you even attempt any form of texturing on her, you might would want to boolean the whole thing together (cause I can see you didn't). That way the model will damage correctly ingame and stuff. BC's engine like seamless, clean meshes.

That is the last thing I do prior to exporting.

baz1701 · « **Reply #112 on:** May 07, 2009, 04:06:17 PM »

some more texture updates

FarShot · « **Reply #113 on:** May 07, 2009, 05:08:38 PM »

Oh wow! These textures are much better in comparison with the ones on your JJPrise. I'm impressed!

baz1701 · « **Reply #114 on:** May 07, 2009, 06:37:47 PM »

Quote from: FarShot on May 07, 2009, 05:08:38 PM

Oh wow! These textures are much better in comparison with the ones on your JJPrise. I'm impressed!

Far more referance pics on this ship than the JJPrise

Shadowknight1 · « **Reply #115 on:** May 07, 2009, 07:20:04 PM »

Woah, the back of the bridge needs a little work...

Other than that, she's looking good

Adonis · « **Reply #116 on:** May 07, 2009, 07:24:49 PM »

Recheck the shape of the plasma grid, it looks off. Also, that recreational deck pic should span the round windows too.

Erk · « **Reply #117 on:** May 07, 2009, 07:44:01 PM »

here are a few more studio model shots if ya need:

http://startrekpropauthority.blogspot.com/2008/05/detailed-photostudy-of-enterprise-8.html (scroll down a bit)

http://www.st-bilder.de/html/constitution2.html (page 3 starts the Ent-A)

http://www.cloudster.com/Sets&Vehicles/STMPEnterprise/STMPEnterpriseTop.htm

hope this help. your model's looking great so far, keep it up!

Billz · « **Reply #118 on:** May 07, 2009, 08:03:09 PM »

You need to round off the edges slightly of the warp pylons and neck connecting the saucer to the engineering hull.

The way they are set up on your model right now makes it look like someone could cut their finger if they were to run them down the edges of the neck and warp pylons.

Other then that, its not bad.

baz1701 · « **Reply #119 on:** May 08, 2009, 05:52:40 AM »

Quote from: Adonis on May 07, 2009, 07:24:49 PM

Recheck the shape of the plasma grid, it looks off. Also, that recreational deck pic should span the round windows too.

The deflector grid was traced off the official TMP blueprints.

I will adjust the rec deck windows.

News:

Author Topic: refit connie (Read 18226 times)